Under Floor Heating Mat – 8m2 area coverage

R2,500.00

Under Floor Heating Mat – 8m2 area coverage.

Our under tile heating mats are extremely easy to use. We offer a step-by-step visual guide as to how to go about your installation. Thus, anyone is able to do their installation as a DIY.

8 in stock

Description

Underfloor Heating Mesh

Under Floor Heating Mat – 8m2 area coverage- 1,5 Kw

Under-Floor-Heating-DIY-Mesh-Mat-1,5-kw
Under-Floor-Heating-DIY-Mesh-Mat-1,5-kw

 

Under Floor Heating Mat – 8m2 area coverage

Under Floor Heating Mat – 8m2 area coverage is a 1,5kw  Heating Mat that fits into a room size of 16m2, covering 50% of the floor surface.  Please bear in mind that you need to purchase a thermostat. We have various models: Analogue, Digital, Programmable and Motion Sensor. They are all suitable for the heating system. The choice is yours. You have an option of buying an alarm to alert you if the heater gets damaged during tiling.

When do I need the External Sensor/Probe connected to the thermostat?

The external sensor/probe is installed on wooden floors, as well as for bathrooms, where the thermostat is installed outside of the heated area.

You can also use it if you want to control the floor temperature of tiled floors, seedling trays, incubators for crocodiles, snakes, etc.

Steps to follow for installations of your underfloor heating mesh mat

Step 1: Make sure the mat you purchased is the correct size for your room. Now you plan the layout of the mat. Start doing this by doing a sketch of the area with the measurements of the mat. Make sure you know where you will be positioning your thermostat. Hence this will be the starting and end point of the mat.

Step 2: Once step 1 is done, make sure your floor surface is clean and level. Hence if there are any rough patches, level them out with a self-levelling screed.

Step 3: Now, starting from the point where you will install your thermostat, roll out your mat to the desired length. Cut the mesh, thus twist the mat, so hence it runs parallel next to rolled out length, be careful not to cut the wire. You may cut away some mesh if you have excess, this could happen when installing in bathrooms. Continue in this fashion until the desired floor space is covered, ending back at the starting point.

Step 4: To hold the mat in place, use strong duct tape, a hot glue gun or nails attached to the mesh, NOT the wire.

Step 5: If you are installing an external sensor ( would be used for bathrooms, cemcrete floors and wooden floors ), this should be perfectly positioned in the middle of the heating wires. If you position it closer to one cable than the other, the temperature would not be gauged properly.

Step 6: If you had purchased an alarm ( ideally you should ), connect the cold tails ( this is the wire at the end of the mat which connects to the thermostat ), to the alarm to ensure the mat did not get damaged. If the alarm sounds, you have a problem.

Step 7:To lay your tiles or floor surface: There are 2 methods, it’s up to your own initiative.

Method 1: You can lay tiles directly on top of the mat ensuring the tile adhesive goes through the mesh to make contact with the concrete floor.

Method 2: Prepare a slurry mixture of self-levelling screed and bonding liquid. Spread this mixture over the mat and leave it to dry. This mixture will get rock-hard. You can now install the floor surface of your choice.

Step 8. Assuming the alarm hasn’t sounded, and the floor surface has been laid, you can now connect the thermostat to the heating system.

In our next blog, we will explain how to connect and position various models of thermostats.

Step 9. Let it dry for a few days before the first usage.

If you are using the wire without the mesh, you should watch the following video link

https://www.youtube.com/watch?v=XozfGnPsm1Q

 

 

Reviews

There are no reviews yet.

Be the first to review “Under Floor Heating Mat – 8m2 area coverage”