Heating Mat for tiles – 6 m2 area coverage


Under Floor Heating Mat – 6 m2 area coverage. 1,2 kW power heater

Our under tile heating mats are extremely easy to use. We offer a step-by-step visual guide on how to go about your installation. Thus, anyone is able to do their installation as a DIY.

(1 customer review)

10 in stock

Only 10 items left in stock!

Heating Mat for tiles – 6 m2 area coverage

Heating Mat for tiles – 6 m2 area coverage is a 1,2 kW Heating Mat that fits into a room size of 12 m2, covering 50% of the floor surface. Please bear in mind that you need to purchase a thermostat. We have various models: Analogue, Digital, Programmable and Motion Sensor. They are all suitable for the heating system. The choice is yours. You have an option of buying an alarm to alert you if the heater gets damaged during tiling.

When do I need the External Sensor/Probe connected to the thermostat?

The external sensor/probe is installed when wooden floors and for bathrooms where the thermostat is mounted outside. It is also used if you want to control the floor temperature of tiled floors, seedling trays, incubators for crocodiles, snakes, etc.

Heating Mat for tiles - 6 m2 area coverage
Heating Mat for tiles – 6 m2 area coverage

Heating Mat for tiles – 6 m2 area coverage – How to install

Step 1: Make sure the size mat you purchased is the correct size for your room. Now you need to plan the layout of the mat. Start doing this by doing a sketch of the room with all measurements of the mat. Also, know where you would be positioning your thermostat, as this would be the starting and end point of the mat.

Step 2: Once step 1 is done, make sure the floor surface is clean and level. If there are any rough patches, level it out with a self-levelling screed.

Step 3: Now, from the point where you would place your thermostat, roll out the mat to the desired length, then cut the mesh to twist the mat to run parallel next to the rolled-out length, be careful not to cut the wire. You may cut away some mesh if you have excess, this could happen when installing in bathrooms. Continue in this fashion until the desired floor space is covered, ending back at the starting point.

Step 4: To hold the Heating Mat for tiles – 6 m2 area coverage in place, use strong duct tape, a hot glue gun or nails attached to the mesh, NOT the wire.

Step 5: If you are installing an external sensor ( would be used for bathrooms, cemcrete floors and wooden floors ), this should be perfectly positioned in the middle of the heating wires. If you position it closer to one cable than the other, the temperature would not be gauged properly.

Step 6: If you have purchased an alarm ( ideally you should ), connect the cold tails ( this is the wire at the end of the mat which connects to the thermostat ), to the alarm to ensure the mat did not get damaged. If the alarm sounds, you have a problem.

Step 7. To lay your tiles or floor surface: There are 2 methods, it’s up to your own initiative.

Method 1: You can lay tiles directly on top of the mat ensuring the tile adhesive goes through the mesh to make contact with concrete floor.

Method 2: Prepare a slurry mixture of self-levelling screed and bonding liquid. Spread this mixture over the Heating Mat for tiles – 6 m2 area coverage and leave it to dry. This mixture will get rock-hard. You can now install the floor surface of your choice.

Step 8. Assuming the alarm hasn’t sounded, and the floor surface has been laid, you can now connect the thermostat to the Heating Mat for tiles – 6 m2 area coverage. In our next blog, we will explain how to connect and position various models of thermostats.

Step 9. Let it dry for a few days before the first usage.

If you are using the wire without the mesh, you should watch the following video link



1 review for Heating Mat for tiles – 6 m2 area coverage

  1. jessicamoses748

    So happy with this product thank you so much JC HEAT 2 TILE and TEAM for all the advice you provided to me

Only logged in customers who have purchased this product may leave a review.